Roofing

1-PART POURABLE PENETRATION SEALANT

1-Part is a moisture curing, pourable sealant designed for use in pitch pans and warranted ChemCurb/E-Curb penetration seals. 1-Part is suitable for application in damp, dry, or cold climates. 1-Part is solvent free, contains no isocyanates and will not shrink upon curing. 1-Part has resilient “elastomeric” properties and excellent adhesion to most construction materials.

View

ChemCurb™ Penetration Seal Components

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water.

View

DuraLink® 35 Multi-Purpose Sealant

DuraLink 35 is a multi-purpose, moisture cure, elastomeric sealant that combines economy and high performance. DuraLink 35 has excellent elastomeric properties which is ideal for a wide range of applications including difficult surfaces such as Kynar 500® PVDF and other anodized metals and coatings. DuraLink 35 is isocyanate free, paintable and SWRI validated for ± 35% joint movement.

View

DuraLink® 50 Super Adhesion Sealant

DuraLink 50 is an extremely elastic, moisture cure, elastomeric sealant designed for use in roofing, cementitious siding, metal architecture, curtain wall construction and joints subject to movement. DuraLink 50 has excellent elastomeric properties which is ideal for a wide range of applications including difficult surfaces such as Kynar 500® PVDF and other anodized metals and coatings. DuraLink 50 is isocyanate free, paintable and SWRI validated for ± 50% joint movement.

View

M-1® Universal Adhesive & Sealant

M-1 is a moisture cure, multi-purpose structural adhesive/sealant designed for bonding and sealing a wide range of construction materials. M-1 forms a tough elastic waterproof seal to most roofing materials, masonry, wood, glass, aluminum and foam. M-1 bonds well to most building surfaces including: metal flashing, copings, skylights, and HVAC surfaces.

View

NovaLink® 35 Joint Sealant

NovaLink 35 is a multi-purpose, moisture cure, construction sealant specially formulated for application in damp, dry and cold conditions. NovaLink 35 is UV resistant and will not suntan. NovaLink 35 is designed for use with many building materials including concrete, glass, metal and most roofing materials. NovaLink 35 seals expansion joints, flashings, windows, doors, and roofing joints. NovaLink 35 is isocyanate free, paintable and SWRI validated for ± 35% joint movement.

View

NovaLink® TX Textured Sealant

NovaLink TX is a gun grade polyether, moisture cure, texturized elastomeric sealant, formulated for use on expansion joints where a textured appearance is required. NovaLink TX has excellent adhesion to most construction materials including cementitious siding, concrete, glass, roofing, metal and Kynar 500® PVDF-coated metals. NovaLink TX is isocyanate free, paintable and validated for ± 35% joint movement.

View

Quick Cut Emulsifying Cleaner

Quick Cut is an industrial strength cleaner specifically formulated to break the soil to surface bond and hold the particles in suspension for easy removal. Quick Cut does not contain any acids, caustic soda, caustic potash, hazardous solvents and VOC’s. Quick Cut emulsifies grease, oil, atmospheric dirt, road film and many other soils without damaging or eating away at the surface. Quick Cut is effective in hot, cold, hard or soft water.

View

ChemCurb™ 1-Part Penetration Seal System

The ChemCurb System replaces the old style metal pitch pans with versatile precast curb components, 1-Part polyether pourable sealant, and structural adhesive/sealant. The system can usually be installed in under 15 minutes and eliminates the need for flashing or mechanical attachment. The ChemCurb System is designed for use on granulated modified bitumen, PVC, EPDM, PIB, TPO single ply, asphalt, and coal tar B.U.R. Please note TPO Primer must be used on TPO single-ply roof substrates. When installed properly, the ChemCurb System forms a durable waterproof rubber seal around penetrations of any size.

View

ChemCurb™ Pro Pack Penetration Seal System

The ChemCurb System replaces the old style metal pitch pans with versatile precast curb components, 2 part urethane pourable sealant, and structural adhesive/sealant. The system can usually be installed in under 15 minutes and eliminates the need for flashing or mechanical attachment. The ChemCurb System is designed for use on granulated modified bitumen, PVC, EPDM, PIB, TPO single ply, asphalt, and coal tar B.U.R. Please note TPO Primer must be used on TPO single-ply roof substrates. When installed properly, the ChemCurb System forms a durable waterproof rubber seal around penetrations of any size.

View

DoubleStick Roof Repair Tape

DoubleStick is an advanced MicroSealant™ tape with a removable siliconized release liner on each side. Designed to bond two surfaces, even two surfaces made of two or more dissimilar materials. DoubleStick creates a tight, permanent, waterproof seal. DoubleStick remains flexible to temperatures as low as -70° F making it virtually impossible to thermally shock the seal causing a leak. DoubleStick bonds to a wide range of surfaces including EPDM, TPO, aged PVC, SBS, APP modifieds, asphalt BURs, coal tar BURs, tiles, shingle, coated and non-coated aluminum and metal roofs, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry, OSB board, shielding membranes, etc.

View

E-Curb™ Penetration Seal Components

E-Curb precast form components are composed of light weight nylon resin. The E-Curb is 2-inches high and is available in a variety of shapes and sizes. Standard sizes include bisected circular pieces with inside diameters of 3, 4, 5, 6 or 9 inches; corner pieces with a 2-inch radius; straight pieces in 3-inch or 8-inch lengths; and a 4.5” x 3.4” rectangle. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light and ponding water.

View

E-Curb™ Penetration Seal System

E-Curb penetration seals replace old-style metal pitch pans with versatile, precast components and 1-Part polyether pourable sealants. CHEM LINK’s E-Curb System can usually be installed in under 15 minutes and never requires flashing or mechanical attachment. E-Curbs are designed for use on granulated modified bitumen, asphalt and coal tar B.U.R. (built up roofing). E-Curbs are specified for PVC, EPDM, PIB, and TPO single ply roofing membranes. E-Curbs are highly versatile for sealing penetrations around solar panel mounts, HVAC, Electrical, and any type of structural supports. TPO Primer is required for use with TPO single-ply roof membrane.

View

DuraSil® SL Self-Leveling Sealant

DuraSil SL is an oxime (neutral) cure silicone sealant designed for use in pitch pans and warranted E-Curb penetration seals. DuraSil SL is suitable for hot pipe applications up to 400°F (204°C). DuraSil SL’s low durometer and resilient “elastomeric” properties accommodate greater movement in penetration seals. DuraSil SL is solvent free, contains no isocyanates and will not shrink upon curing.

View

FlashPack Liquid Flashing

FlashPack Liquid Flashing is designed to waterproof around odd shaped roof penetrations in difficult flashing conditions. FlashPacks components are moisture curing which will not out-gas or bubble on damp surfaces as urethane sealants do. FlashPack is suitable for many construction site conditions dealing with wet or dry climates and low temperatures down to (32°F/ 0°C). FlashPack is solvent free and will not shrink upon curing. FlashPack is compatible with many substrates including concrete, masonry, wood and granule surfaced BUR and SBS cap sheets. A granulated target should be applied first before using FlashPack on smooth APP. FlashPack is compatible with most metals excluding Kynar and copper.

View

Hot Pipe E-Curb™ Penetration Seal System

Hot Pipe E-Curb penetration seals replace old-style metal pitch pans with versatile, precast components and RTV silicone pourable sealants for installations requiring a service temperature between -80°F to 400°F (-62°C to 204°C). CHEM LINK’s Hot Pipe E-Curb System can usually be installed in under 15 minutes and never requires flashing or mechanical attachment. E-Curbs are designed for use on granulated modified bitumen, asphalt and coal tar B.U.R. (built up roofing). E-Curbs are specified for PVC, EPDM, PIB, and TPO single-ply roofing membranes. E-Curbs are highly versatile for sealing penetrations around HVAC, mechanical, solar panel mounts, electrical, and any type of structural supports. TPO Primer is required for use with TPO single-ply roofing membrane.

View

Low VOC EPDM/TPO Primer

A solvent based liquid primer that is designed to comply with VOC regulations. It can be brush applied to EPDM or TPO roofing membranes, plastics, and any other difficult bonding surface.

View

Metal Roof E-Curb™ Penetration Seal System

Metal Roof E-Curb penetration seals replace old-style rubber boots with versatile, precast components and non-sag 1-Part polyether sealants for installations on a sloped substrate. Chem Link’s Metal Roof E-Curb System can usually be installed in under 15 minutes and never requires flashing or mechanical attachment. E-Curbs are designed for use on metal roofing systems that require adhesion to Kynar 500® PVDF coated metals. E-Curbs are highly versatile for sealing penetrations around HVAC, mechanical, solar panel mounts, electrical, and any type of structural supports. TPO Primer is required for use with TPO single-ply roofing membrane.

View

MetaLink High Performance Metal Roof Sealant

MetaLink is a multi-purpose neutral cure silicone construction sealant specially formulated for application in a variety of job site conditions. MetaLink is UV resistant. MetaLink is designed for use with many building materials including galvanized aluminum, metal, Kynar 500 PVDF coated metal, glass, and most roofing materials. MetaLink is available in a wide range of colors to match contemporary tastes in decorative metal roof and siding products. MetaLink is isocyanate free and validated for ± 50% joint movement.

View

Pro Pack® Urethane Pourable Sealant

Pro Pack is a two-component, RTV, urethane pourable sealant. It is designed for use to fill warranted ChemCurb penetration seals & pitch pans on low-slope roofing systems. It can also be used in horizontal self-leveling, sealing and waterproofing applications. When properly mixed, Pro Pack cures to a tough rubber mass with excellent low temperature elasticity and adhesion. Pro Pack resists deterioration caused by weather, water and ice. It is also resistant to oils, fuels, and many chemicals. Pro Pack is 100% solid rubber. Pro Pack has no solvents, very low volatile organic content (V.O.C) and will not shrink after application. Pro Pack has excellent adhesion to most construction materials.

View

RoofSeal Roof Repair Tape

For use on virtually all roofs, RoofSeal features a UV stable backing that is available in Black, Gray, Tan and White. With the exception of surface prep, RoofSeal is a one-step permanent repair system for virtually all roof types, and roof accessories. RoofSeal creates a waterproof, moisture, and air tight barrier with no additional sealing required. RoofSeal remains flexible to temperatures as low as -70° F making it virtually impossible to thermally shock the seam causing a leak. RoofSeal bonds to a wide range of surfaces including difficult roof materials such as EPDM, TPO, aged PVC, SBS, APP modifieds, asphalt BURs, coal tar BURs, all metal roofs, tiles, shingle, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry, OSB, etc.

View

SBS-Modified Bitumen Adhesive

SBS-Modified Bitumen Adhesive is a solvent free, moisture cure adhesive designed for easy installation of bituminous membranes in difficult wet or cold environments without sacrificing performance. SBS-Modified Bitumen Adhesive is a unique, isocyanate free formula that is safe for occupied buildings such as schools, hospitals, or food processing plants where solvent vapors are not tolerated. SBS-ModifiedBitumen Adhesive permits installation directly to solvent sensitive or heat sensitive materials such as EPS insulation, iso-board, or fiber recovery board where torches cannot be used. SBS-Modified Bitumen Adhesive contains very low levels of VOC’s, is environmentally compliant throughout North America, and may be used in urban areas where hot asphalt kettles are prohibited or impractical. SBS-Modified Bitumen Adhesive is OSHA compliant and eliminates chronic exposure hazards inherent to solvent based adhesives.

View

Single-Ply EPDM Adhesive

Single-Ply EPDM Adhesive is a 100% solvent free, moisture cure, single coat adhesive that is used to fully adhere EPDM rubber. Wall and curb flashings still require a coating of the underside of the rubber and flashing. Unlike water based adhesives, Single-Ply EPDM Adhesive cannot freeze and be damaged in storage and shipping in freezing temperatures. This unique product is virtually odor free which allow the adhesive to be used in a wide variety of job site environments and can be used in all fifty states without restriction. Single-Ply EPDM Adhesive has a patented, moisture cure formula that offers easy installation of EPDM in difficult, damp or cold environments. It is safe for occupied buildings such as schools, offices, hospitals, or food processing plants, where solvent vapors and odors are not tolerated. Single-Ply EPDM Adhesive bonds aggressively to iso-board, gypsum composite recovery boards and most other construction surfaces. The adhesive is environmentally compliant, solvent free and contains very low levels of VOC’s. Single-Ply EPDM Adhesive can be shipped and used throughout the United States without restriction, is OSHA compliant and eliminates chronic exposure hazards associated with conventional solvent release.

View

SnowShoes – Snow Retention System

SnowShoes are molded from a tough polycarbonate polymer that can withstand heavy impacts at low temperatures. Effective on all metals, including Kynar 500® PVDF coated metal and copper. Also for use on slate, tile, EPDM rubber and PVC and TPO membranes. TPO primer is required with TPO membrane installation. SnowShoes are designed with a unique “stealth” profile to be strong and inconspicuous. They are molded with a translucent matt finish that picks up the background color of roofing materials without reflecting sunlight. Paintable if strict color matching is required. Installation is easy with translucent DuraSil™ adhesive provided in every kit. No screws or mechanical fasteners are ever required. DuraSil bonds aggressively to all roofing materials, including Kynar finishes. It bridges irregularities and will never shrink.

View

Steep Slope E-Curb Penetration Seal System

Steep Slope E-Curb penetration seals replace old-style metal pitch pans with versatile, precast components and non-sag 1-Part polyether sealants for installations on a sloped substrate. Chem Link’s Steep Slope E-Curb System can usually be installed in under 15 minutes and never requires flashing or mechanical attachment. E-Curbs are designed for use on granulated modified bitumen, asphalt and coal tar B.U.R. (built up roofing). E-Curbs are specified for PVC, EPDM, PIB, and TPO single-ply roofing membranes. E-Curbs are highly versatile for sealing penetrations around HVAC, mechanical, solar panel mounts, electrical, and any type of structural supports. TPO Primer is required for use with TPO single-ply roofing membrane.

View

TileSecure Roof Tile Adhesive

TileSecure is a one part, moisture cure, adhesive designed for quick and easy application and repair of clay, masonry and slate roof tiles. It creates a tough, semi flexible seal, quickly and economically that requires no mixing or preparation. TileSecure is isocyanate free, paintable and validated for ± 35% joint movement.

View

WebSeal Roof Repair Tape

For use on virtually all roofs, WebSeal is designed to hold coatings, whether water or solvent based. WebSeal makes the roof water-tight prior to application of coating, creating a superior, faster method of waterproofing over conventional 3 course applications, eliminating dependence on the roof coating as a water barrier. WebSeal remains flexible to temperatures as low as -70° F making it virtually impossible to thermally shock the seam causing a leak. WebSeal bonds to a wide range of surfaces including difficult roof materials such as EPDM, TPO, aged PVC, SBS, APP modifieds, asphalt BURs, coal tar BURs, plus all metal roofs, tiles, shingle, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, fiberglass, brick, concrete, masonry, OSB, etc.

View